TestEquity 123H Temperature/Humidity Chamber (Environmental Chamber)

Additional Product Information

The Features You Want - Included at No Extra Charge...

Programmable Temperature/Humidity Controller
Up to 256 steps can be programmed into as many as 40 nameable profiles. A large LED readout indicates the actual chamber temperature with 0.1° resolution. The context sensitive information key and guided steps make profile programming fast and easy. A four-line backlit LCD displays relative humidity with 0.1% RH resolution, programming, setup, operating and help information. Internal logic provides refrigeration compressor control for responsive and reliable performance. Includes event outputs to control remote devices. RS-232C interface is also included. GPIB, Ethernet and analog retransmit outputs are available as options.
More about the Temperature/Humidity Controller >>
RS-232 Programming Resources >>
GPIB Programming Resources and LabVIEW drivers >>
Ethernet Interface Information >>

High/Low Temperature Limit Controller and Alarm
Provides independent protection against excess temperatures. Both high and low limits can be set. The upper LED readout indicates the actual chamber temperature while the lower readout indicates the status The limit controller will shut down the chamber and trigger the audible alarm in the event of an out of limit condition. A set of uncommitted contacts are available to provide a safety power interlock for your test sample.

Accurate Humidity Measurement
A fast responding Vaisala capacitive-type sensor eliminates the need for unreliable wet-wicks.

GN2 Purge Capability Standard
For low humdity conditions below 6°C Dewpoint (requires customer-supplied gaseous nitrogen supply). More Info >>

Optional Dry Air Purge Capability - Field Upgradeable
Optional Dry Air Purge is easy to add in the field (requires customer-supplied compressed air supply). More Info >>

Event Relays Standard
Four uncommitted solid-state relays are provided to switch the power to remote AC devices via the F4 Temperature/Humidity Controller.

120 Volt Input The chamber draws 18 Amps maximum at 120 Volts. You can plug it into any standard 20 Amp wall receptacle.

Viewing Window
Heated multi-pane window eliminates fog and condensation without a manual wiper.

Two 4" Access Ports
Lets you attach wires and sensors to your test sample through both the left and right side of the chamber.

Adjustable Shelf
A heavy-duty stainless steel wire shelf ensures proper airflow around your test sample for uniform temperature distribution.

Casters
Rugged casters permit easy movement.

World's Best Environmental Chamber Warranty
Only TestEquity offers a 3-year warranty on parts and 1-year warranty on labor. Our nationwide service network is qualified to do the job right. And we always have replacement parts in stock for immediate shipment. Labor warranty applies to the United States and Canada only. See the complete warranty statement here.

TECHNICAL FEATURES

Accurate Humidity Measurement
A fast responding capacitive-type sensor eliminates the need for unreliable wet-wicks.

Reliable Vapor Generator
Unlike "atomizing" systems, the heated vapor generator has no pump to fail or orifice to clog. The stainless-steel vapor generator assembly is double-protected against low-water and over-temperature conditions. A float switch senses low-water level. The immersion heater has an embedded thermocouple for ultimate thermal protection.

No-Sweat Cabinet
We use a combination of structural foam and fiberglass blanket insulation for a higher combined R-factor than just fiberglass alone. The door sealing surface is kept warm by circulating excess heat from the refrigeration system. The result is a cabinet that does not sweat due to condensation during low temperature operation.

Water Recirculation System
The optional water recirculation system provides a reliable source of demineralized water for the humidity system, using ordinary tap or pre-filtered water. Condensate from the chamber is returned back to the water tank. The recirculation pump operates only when needed to fill the chamber's humidifier to the correct level. Perfect for installations where a water line and drain are not available.
(Optional, and highly recommended) More Info >>

Reliability & Safety That's Designed In
Non-CFC refrigerants are used in a cascade (two compressors) configuration. Expansion valves provide optimum performance throughout the operating range. Pressure regulators keep the operating pressures within safe limits regardless of load conditions. Liquid injection ensures cool compressor operation during high-temperature pull down for long life. Sequential starting of each compressor reduces the current demand on start-up. Each compressor is protected by high/low pressure switches. Care has been taken to use a minimum number of fittings, joints and welds to reduce the possibility of refrigerant leaks.

All electrical control components are UL approved. The nichrome air-heater has a low watt-density and even heat distribution for reliable performance and fast response. A fusible link provides fail-safe protection against thermal runaways, in addition to the microprocessor-based high/low limit controller.

The side and rear panels are removable to permit complete access to the refrigeration and humidity system for ease of service and preventive maintenance.

PRICING INFORMATION

TestEquity 123H Temperature/Humidity Chamber (Environmental Chamber) 2.3 Cu Ft Workspace, -68°C to +175°C, Humidity 10% to 95% RH (Limited by a 6°C dewpoint and maximum dry bulb of +85°C. Derate to 90% over 65°C.)	TEVET Price $16,039

OPTIONS & ACCESSORIES

0016 Water Recirculation System For Model 123H. Provides a reliable supply of filtered water for the humidity system. Perfect for installations where a water line and drain are not available. Uses 0014 filters. Highly Recommended! More info >>	TEVET Price $1,049
0014 Replacement Water Filters (Box of 6) For use with 0010 and 0016 Water Recirculation Systems.	TEVET Price $595
0017 Dry Air Purge for 123 Can be added in the field. Heatless regenerative desiccant air drier. Requires 5 cfm supply air flow rate at 100 psig (175 psig max) to be supplied by customer. More info >>	TEVET Price $2,095
0022 Circular Chart Recorder (Factory Installed) Honeywell DR4300 Series. Two pen, 10" circular chart. Records chamber temperature and humidity. 24-hour rotation.	TEVET Price $1,495
0011 Replacement Water Filters Box of 6 Water Filters for 200H Series	TEVET Price $525
0231 Extra Shelf with Clips for Model 123 Chamber comes standard with one shelf.	TEVET Price $79
1052 GPIB Interface (External interface converter box) Converts the temperature controller's serial interface to GPIB. More info >>	TEVET Price $895
1055 Ethernet Interface (External interface converter box) Converts the temperature controller's serial interface to Ethernet. Not compatible with GPIB Option 0003 (Internal GPIB Converter). If you want the capability of both GPIB and Ethernet you must order GPIB Option 1052 (External GPIB Converter) More info >>	TEVET Price $895
0004 Controller Retransmit Outputs (Installed) Analog retransmit of chamber temperature, set point (or %RH on 123H and 1007H). Two outputs. More info >>	TEVET Price $195
300534 Port Plug, Silicone Foam, 4" D x 4" L Open-cell silicone sponge with closed-cell silicone facing.	TEVET Price $50